The CentOS 6 official software repositories has PHP 5.3 which has reached end of life and no longer actively maintained by the developers. To keep up with the latest features and security updates, you need a newer (probably the latest) version of PHP on your CentOS 6 system. If you’re looking to install different versions of PHP in CentOS 6, go through the following article.
For the purpose of this guide, we will be operating the system as root, if that is not the case for you, make use of the to acquire root privileges. Installing PHP 7 on CentOS 7 1. To install latest PHP 7, you need to add EPEL and Remi repository to your CentOS 6 system like so. # yum install # yum install 2.
![]()
Now install yum-utils, a group of useful tools that enhance yum’s default package management features. Yum-utils can be used for manipulating package repositories and additional package management operations such as enabling or disabling packages without any manual configuration by a system administrator. You can install it as follows: # yum install yum-utils 3. In this step, you need to enable Remi repository using yum-config-manager utility, as the default repository for installing PHP. # yum-config-manager -enable remi-php70 Install PHP 7.0 If you want to install PHP 7.1 or PHP 7.2 on CentOS 6, just enable it as shown. # yum-config-manager -enable remi-php71 Install PHP 7.1 # yum-config-manager -enable remi-php72 Install PHP 7.2 4. Then finally install PHP 7 on CentOS 6 with all necessary PHP modules using the following command.
# yum install php php-mcrypt php-cli php-gd php-curl php-mysql php-ldap php-zip php-fileinfo.
![]()
On this page. SuPHP is an apache module that allows PHP to under a different Linux user than the apache user. This improves the security of hosted websites as you can run the PHP scripts of each website under a different user. This tutorial describes the installation of SuPHP on centOS 7.2 from source as there are no SuPHP packages available for CentOS 7.2. Prerequisites You shall have a server that has CentOS 7.2 or later installed, I will use as basis for my setup. In the first chapter, I will install the Apache web server. If you have apache already installed, then start with chapter 2 right away.
My server will use the hostname server1.example.com and the IP address 192.168.1.100. Replace these values with the hostname and IP of your server wherever they occur in the following tutorial. I recommend to have a firewall installed for security reasons, if you do not have firewalld installed yet, then you can install it with these commands: yum -y install firewalld start the firewall and enable it to be started at boot time.
Systemctl start firewalld.service systemctl enable firewalld.service Next, open your SSH port to ensure that you will be able to connect to the server by SSH. Firewall-cmd -permanent -zone=public -add-service=ssh firewall-cmd -reload 1 Installation of Apache 2.4 and PHP 5 Apache and PHP are available in the CentOS base repository, so we can install both software packages with yum.
Install Apache and the Aapache development package which contains files that are required for the SuPHP compilation later. Yum -y install httpd httpd-devel PHP installation (I've added some frequently used PHP modules): yum -y install php php-mysql php-gd php-pear php-xml php-xmlrpc php-mbstring curl We have to enable Apache to start at boot time and start the service. Systemctl start httpd.service systemctl enable httpd.service We have to open the HTTP (80) and HTTPS (443) ports to make the web server accessible from other computers. Run the following commands to configure the firewall. Firewall-cmd -permanent -zone=public -add-service=http firewall-cmd -permanent -zone=public -add-service=https firewall-cmd -reload 2 Installation of SuPHP We will compile SuPHP from source in this step.
Install the development tools to setup the required build chain. Yum -y groupinstall 'Development Tools' And wget to download the source files and the nano editor. Yum -y install wget nano Download the SuPHP source tar.gz archive and unpack it. Cd /usr/local/src wget tar zxvf suphp-0.7.2.tar.gz CentOS 7 uses Apache 2.4, so we have to patch suphp before we can compile it aganst Apache.
The patch gets applied like this: wget -O suphp.patch patch -Np1 -d suphp-0.7.2 DocumentRoot /var/www/example.com ServerName example.com ServerAdmin SetHandler None suPHPEngine on SetHandler x-httpd-suphp suPHPAddHandler x-httpd-suphp Replace the domain name with your own domain in the ServerName and ServerAdmin lines. Then restart apache to apply the config changes. Systemctl restart httpd.service 4 Test the SuPHP setup In this chapter, I will show you several methods to test PHP in this website.
Centos 6 Iso
First, I will create a file that uses the phpinfo function to show if PHP is working and if it runs in CGI mode now. Create an info.php file with nano: nano /var/www/example.com/info.php and add the following lines to the new file. After following the entire steps when i run the server i'm getting the php code directly. There is no error is added in suphplog. But in errorlog i got like below. Thu Jun 30 13:28 2016 mpmprefork:notice pid 26530 AH00170: caught SIGWINCH, shutting down gracefully Thu Jun 30 13:75 2016 core:notice pid 26560 SELinux policy enabled; httpd running as context systemu:systemr:httpdt:s0 Thu Jun 30 13:73 2016 suexec:notice pid 26560 AH01232: suEXEC mechanism enabled (wrapper: /usr/sbin/suexec) Thu Jun 30 13:10 2016 authdigest:notice pid 26560 AH01757: generating secret for digest authentication.
Thu Jun 30 13:23 2016 lbmethodheartbeat:notice pid 26560 AH02282: No slotmem from modheartmonitor Thu Jun 30 13:36 2016 mpmprefork:notice pid 26560 AH00163: Apache/2.4.6 (CentOS) PHP/5.4.16 configured - resuming normal operations Thu Jun 30 13:74 2016 core:notice pid 26560 AH00094: Command line: '/usr/sbin/httpd -D FOREGROUND' I don't know what is the issue. Could you please help me on this.
1 Preliminary Note I'm using a CentOS 6.2 server in this tutorial with the hostname server1.example.com and the IP address 192.168.0.100. I will create two Apache vhosts in this tutorial, www.example1.com and www.example2.com, to demonstrate the usage of modfcgid.
Install Apache Centos
Before we start, make sure that SELinux is disabled. Edit /etc/selinux/config and set SELINUX=disabled: vi /etc/selinux/config # This file controls the state of SELinux on the system. # SELINUX= can take one of these three values: # enforcing - SELinux security policy is enforced. # permissive - SELinux prints warnings instead of enforcing. # disabled - No SELinux policy is loaded. SELINUX=disabled # SELINUXTYPE= can take one of these two values: # targeted - Targeted processes are protected, # mls - Multi Level Security protection. SELINUXTYPE=targeted Afterwards we must reboot the system: reboot 2 Installing Apache2/modfcgi/PHP5 modfcgid is not available in the official CentOS repositories, but there's a package in the EPEL repository.
![]()
We enable the repository as follows: rpm -import wget rpm -ivh epel-release-6-7.noarch.rpm yum install yum-priorities Edit /etc/yum.repos.d/epel.repo. Vi /etc/yum.repos.d/epel.repo. And add the line priority=10 to the epel section: epel name=Extra Packages for Enterprise Linux 6 - $basearch #baseurl=mirrorlist=failovermethod=priority enabled=1 priority=10 gpgcheck=1 gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-EPEL-6. Afterwards we can install Apache2, modfcgid, and PHP5: yum install httpd modfcgid php-cli If Apache2 was already installed with PHP5 as an Apache module, disable the PHP5 module now - open /etc/httpd/conf.d/php.conf.
Vi /etc/httpd/conf.d/php.conf. And comment out everything in that file: # # PHP is an HTML-embedded scripting language which attempts to make it # easy for developers to write dynamically generated webpages. # # # LoadModule php5module modules/libphp5.so # # # LoadModule php5module modules/libphp5-zts.so # # # Cause the PHP interpreter to handle files with a.php extension. # #AddHandler php5-script.php #AddType text/html.php # # Add index.php to the list of files that will be served as directory # indexes. # #DirectoryIndex index.php # # Uncomment the following line to allow PHP to pretty-print.phps # files as PHP source code: # #AddType application/x-httpd-php-source.phps Then we create the system startup links for Apache and start it: chkconfig -levels 235 httpd on /etc/init.d/httpd restart Next we open /etc/php.ini. Vi /etc/php.ini. And uncomment the line cgi.fixpathinfo=1:.; cgi.fixpathinfo provides.real.
PATHINFO/PATHTRANSLATED support for CGI. PHP's; previous behaviour was to set PATHTRANSLATED to SCRIPTFILENAME, and to not grok; what PATHINFO is. For more information on PATHINFO, see the cgi specs. Setting; this to 1 will cause PHP CGI to fix its paths to conform to the spec. A setting; of zero causes PHP to behave as before. Default is 1. You should fix your scripts; to use SCRIPTFILENAME rather than PATHTRANSLATED.; cgi.fixpathinfo=1.
Open /etc/httpd/conf.d/fcgid.conf. Adobe premiere pro cs6 32 bit portable north. Vi /etc/httpd/conf.d/fcgid.conf.
And add the line PHPFixPathinfoEnable 1 at the end:. PHPFixPathinfoEnable 1 Then reload Apache: /etc/init.d/httpd reload 3 Creating Vhosts For www.example1.com And www.example2.com I will now create two vhosts, www.example1.com (with the document root /var/www/web1/web) and www.example2.com (with the document root /var/www/web2/web). Www.example1.com will be owned by the user and group web1, and www.example2.com by the user and group web2. First we create the users and groups: groupadd web1 groupadd web2 useradd -s /bin/false -d /var/www/web1 -m -g web1 web1 useradd -s /bin/false -d /var/www/web2 -m -g web2 web2 chmod 755 /var/www/web1 chmod 755 /var/www/web2 Then we create the document roots and make them owned by the users/groups web1 resp.
Virtualmin GPL Installer The installer should only be used on systems that are not currently running Webmin or hosting any websites. Ideally, it should be run on a system that has a fresh install of either CentOS 5, Debian 4.0, Ubuntu 8.04 or Solaris as at the moment those are the only supported operating systems. Further documentation on supported systems and install requirements is available on the. The Linux installer can be downloaded from. Once you have it on the Linux system you want to run Virtualmin on, execute it with the commands: chmod +x install.sh./install.sh The Solaris installer can be downloaded from. The commands to run it on your Solaris Sparc or X86 system are: chmod +x solaris-install.sh./solaris-install.sh Because it downloads numerous packages from the Virtualmin website and your Linux distribution's repository, it may take up to 30 minutes for the install to complete.
Soundflower app. Apr 23, 2016. SoundFlower was working fine on my mac to enable me. Threads about Mountain Lion OS problems and Soundflower. Soundflower problems - Mountain Lion.
Once it is done, you can login to Webmin at to see the Virtualmin user interface. Virtualmin GPL Repository One of the main advantages of using the installer over setting up Virtualmin manually is the APT or YUM repository that it sets up on your system. This includes Debian or RPM packages for Webmin, Usermin and the Virtualmin modules, plus modified versions of dependent programs like Apache and PHP. When updates to Virtualmin-related packages are available, they will be displayed on the System Information page that appears on the right-hand frame after logging in. You can install all updates with the click of a button, or use the Virtualmin Package Updates module to install them selectively.
There are plenty of tutorials on the web. Tons and tons. However when I had to create working configuration and put together Virtualmin template most of these instruction just didn’t work properly. After some time I’ve came up with my own working configuration and proper Virtualmin apache template for CentOS. As a bonus we’ll have per-user php.ini and apache2 worker MPM which is a little bit faster and less resource hungry then traditional prefork MPM. First, I turned for instructions to, which is proven to be an excellent resource, but unfortunately, instructions they provided are a little bit incomplete. Below is my instructions collected from various sources and tested numerous times.
Install rpms – httpd, php-common, modfcgid, additional php modules you might need. Open /etc/httpd/conf.d/php.conf in your favorite editor and comment out everything. As an alternative you can rename php.conf into php.conf.bak which will prevent apache from loading this config file. C-media usb sound driver. Here is my variant of /etc/httpd/conf.d/fcgid.conf – your can customize it as you see fit.
Comments are closed.
|
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |